3TCGARAGE.COM

1 Back to turbo questions: What would be a good price friendly / readily available turbo to run in a stock 2tc engine? I am thinking somewhere in the 150-175 HP range.

2 Would you recommend an intercooler?

I have a t5 Garrett from a 4cyl Volvo, but I think it is for too large of an engine and I'm sure the pitch of the turbines are all wrong. I would like to run 91 octane.

it will work as long as you dont overboost it but keep it in the safe zone of 5 psi and thats it "only".

my set up just as an fyi.
hx35 turbo T3 flange
1.8 bored 87mm
forged eagle rods wiseco 7:1 compression pistons
head work done up the butt
double valve springs
stainless steel valves
bronze valve guides
5 angle valve job
turbo cam and degree wheel
balanced everything
log exhaust manifold evil140
2tg intake maifold
1200cc injectors RC
bosch 044 fuel pump
-8 pressure feed line
-6 return
efi ms2 v3.0 with edis4 for spark


and thats just to make 475hp on the safe side

I like the simplicity of your build 475HP is an lot

hemilove wrote:it will work as long as you dont overboost it but keep it in the safe zone of 5 psi and thats it "only".

my set up just as an fyi.
hx35 turbo T3 flange
1.8 bored 87mm
forged eagle rods wiseco 7:1 compression pistons
head work done up the butt
double valve springs
stainless steel valves
bronze valve guides
5 angle valve job
turbo cam and degree wheel
balanced everything
log exhaust manifold evil140
2tg intake maifold
1200cc injectors RC
bosch 044 fuel pump
-8 pressure feed line
-6 return
efi ms2 v3.0 with edis4 for spark


and thats just to make 475hp on the safe side

hemilove wrote:it will work as long as you dont overboost it but keep it in the safe zone of 5 psi and thats it "only".

my set up just as an fyi.
hx35 turbo T3 flange
1.8 bored 87mm
forged eagle rods wiseco 7:1 compression pistons
head work done up the butt
double valve springs
stainless steel valves
bronze valve guides
5 angle valve job
turbo cam and degree wheel
balanced everything
log exhaust manifold evil140
2tg intake maifold
1200cc injectors RC
bosch 044 fuel pump
-8 pressure feed line
-6 return
efi ms2 v3.0 with edis4 for spark


and thats just to make 475hp on the safe side

In for dino video

Carlos is that HP Horse Power or CH Cabra Power just kidding bro

BOBLOOK wrote:Carlos is that HP Horse Power or CH Cabra Power just kidding bro

Lol its chuppa cabra power!


Its taken I while but I'm almost there brochachos

hemilove wrote:it will work as long as you dont overboost it but keep it in the safe zone of 5 psi and thats it "only".

my set up just as an fyi.
hx35 turbo T3 flange
1.8 bored 87mm
forged eagle rods wiseco 7:1 compression pistons
head work done up the butt
double valve springs
stainless steel valves
bronze valve guides
5 angle valve job
turbo cam and degree wheel
balanced everything
log exhaust manifold evil140
2tg intake maifold
1200cc injectors RC
bosch 044 fuel pump
-8 pressure feed line
-6 return
efi ms2 v3.0 with edis4 for spark


and thats just to make 475hp on the safe side

What trans will you be using for this power level. Pretty similar to the levels I'm looking for.

W50 steel case homie its good for the power

hemilove wrote:W50 steel case homie its good for the power

Extremely happy to hear that. Been on edge about my W58 holding up, glad someone says it will

Look runs 9.7s on the 1/4 mile witha celica tranny and makes close to 500 hp check the vids. This means the trany holds power. http://m.youtube.com/watch?v=6R_Yn5-5w6 ... TPpoHGJJBM