Te71 Coupe

Moderators: BOBLOOK, AE25, pufito18

Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

Image
Going to paint it when the rack and pinion is on place.

Image

Toyota didnt sell me orginal 3tgteu one so have to make it from and old 2t dizzy.
Image
Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

Image
Image
Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

Image
Image

Got my "dizzy" back.
Image
BOBLOOK
Posts: 2334
Joined: Wed Jun 19, 2013 7:32 pm
Location: Under a bonned in Netherlands.

Re: Te71 Coupe

Post by BOBLOOK »

waste spark ?
The day we learn to think
Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

BOBLOOK wrote:waste spark ?
Yep.
Image
Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

This isn,t going too good :x

Image

This is with new cheap main bearings. So measured the caps, 4 of those cos the machine was too small for measure the 3. cap.
1= 62.012
2= 62.032
3=?
4=62.041
5=62.037

and crank was:
1= 57.965
2=57.970
3= 57.970
4=57.970
5=57.960

IF the bearings are 2mm there is 0.077 oil clearance in 5. I ordered std king bearings and try with those, lets see how it goes. :roll:
Image
BOBLOOK
Posts: 2334
Joined: Wed Jun 19, 2013 7:32 pm
Location: Under a bonned in Netherlands.

Re: Te71 Coupe

Post by BOBLOOK »

Wow oldschool haven't see those measurement method for almost 20 years :lol: :lol: Are you cutting the crank down ?
The day we learn to think
Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

BOBLOOK wrote:Wow oldschool haven't see those measurement method for almost 20 years :lol: :lol: Are you cutting the crank down ?
Good measure method :D No, i dont cut crank. I ordered better quality bearing and installed those.
Image
BOBLOOK
Posts: 2334
Joined: Wed Jun 19, 2013 7:32 pm
Location: Under a bonned in Netherlands.

Re: Te71 Coupe

Post by BOBLOOK »

Oh okay good luck with the build
The day we learn to think
Heiska
Posts: 117
Joined: Tue Jun 25, 2013 3:38 am

Re: Te71 Coupe

Post by Heiska »

Has been while :D

Just boughted nissan 200 sx front end, few pics of them compared to te71

te71 bush is 12mm hole and nissan is 14mm
Image

Controll arm bolts are: te71 10mm, nissan 12mm
Image

+bigger brakes
+better bearing
+No ae86 prices :D
+same bolt pattern

Nissan crossmember is also quite similar only 0,5cm differense on the bolt holes.
Image
Image
Post Reply