Search found 95 matches

by Kenny727
Wed Oct 21, 2015 12:55 am
Forum: Project Gallery
Topic: My 82 Corolla SR-5 Couple - Project
Replies: 4
Views: 7174

Re: My 82 Corolla SR-5 Couple - Project

nice sr5 two tone like it , this mine located in southwest http://i61.tinypic.com/fcpgmd.jpg Nice! I like it, it's really simple and clean on the outside. I'm planning on going all flat black in a week or so, will post pics when I finish. Just bored out my Webber carb and Intake mani... I didn't ge...
by Kenny727
Sun Oct 18, 2015 7:51 am
Forum: Exterior Tech
Topic: te27 hood vents?
Replies: 5
Views: 10886

Re: te27 hood vents?

I vented mine by adding washers where the hood attaches... Since I have no accessories even heat, I really on the heat poring out right on my windshield which it does.. Now I just need to find a way to fore more cold air in the front.. Then again I'm doing mine for best engine performance not looks....
by Kenny727
Wed Oct 14, 2015 3:41 am
Forum: Project Gallery
Topic: My 82 Corolla SR-5 Couple - Project
Replies: 4
Views: 7174

My 82 Corolla SR-5 Couple - Project

Hey all, I figured since I'm on this site enough I should post newer pictures of the tings I'm doing to my car, I will upload them tomorrow after work. My Plans: I want a VERY reliable car (Will be driven to work most days), Now my personal preference is that it can be scratched, faded or peeling as...
by Kenny727
Wed Oct 14, 2015 3:04 am
Forum: Engine and Drivetrain
Topic: Best head for a 3t-c?
Replies: 9
Views: 14107

Re: Best head for a 3t-c?

I'm hoping to do a head up build..
So from what your saying a 2t is just as good as 3t if I build it right?
Thanks for the valve size clearace.
What about shaving it down for more compression? any specific number for that?
by Kenny727
Mon Oct 12, 2015 12:58 am
Forum: 101 Frequently Asked Toyota Q\'s Answered
Topic: Easiest engine to replace my 3t-c with?
Replies: 9
Views: 16246

Easiest engine to replace my 3t-c with?

I'm about to start doing a lot of engine work and I want to price an engine swap to see if it will be a better idea. I figure this should be in a frequently asked questions because anyone wanting to know what engines are worth throwing into the "Rolla". (1982 Corolla w/ 3tc 5 speed) Pretty...
by Kenny727
Mon Oct 12, 2015 12:23 am
Forum: Engine and Drivetrain
Topic: Best head for a 3t-c?
Replies: 9
Views: 14107

Re: Best head for a 3t-c?

Is there somewhere that has the info on max valve size, and how much I can shave the head for clearance for both of the heads? I cant find any info about the specific sizes or max sizes. Random question also Whats the max bore keeping it reliable? The racing 4T-GTE with the same block is bored to a ...
by Kenny727
Sun Oct 04, 2015 5:10 am
Forum: Turbo and Engine Management
Topic: Coil on plug VS MSD with distributor.
Replies: 11
Views: 20042

Re: Coil on plug VS MSD with distributor.

Heiska wrote:
BOBLOOK wrote:Msd al the way

After you install turbo you lock the dizzy :ugeek:
Why not COP? Im planning to use yaris (1nz-fe) coils on mine.

How can you use a 1nz-fe coil on a 3TC? I'm really interested.. Searched cant find anything.
by Kenny727
Sun Oct 04, 2015 5:02 am
Forum: Electrical
Topic: Where to wire my Sunpro Tach too?
Replies: 8
Views: 14549

Re: Where to wire my Sunpro Tach too?

No the dizzy don't read tach signal The wire shouldn't be an problem How did you hooked wires colors ? I have it wired: Black to Ground Red to Switched power White to Switched power (Keep the light on) Green to negative on coil The - on the coil only has the green wire, and black from the ignitor. ...
by Kenny727
Sun Oct 04, 2015 4:55 am
Forum: Engine and Drivetrain
Topic: Best head for a 3t-c?
Replies: 9
Views: 14107

Re: Best head for a 3t-c?

I have a 3tc head and a early 1973 2tc head pre smog which one should i use for turbo and should i port it ? Since The 2T head has higher compression,so unless your building bottom end, Id take the 3T and find somewhere that will bore it and throw in bigger valves. from what I hear 2T on 3t block =...