Search found 57 matches

by chesmari
Thu Dec 31, 2015 6:16 am
Forum: Turbo and Engine Management
Topic: EFI Fuel Tank Options
Replies: 15
Views: 35927

Re: EFI Fuel Tank Options

Interesting I also ran a surge tank when I injected my TA27 but have had several issues that I hope to have finally worked out but I used the same set up basically but the fuel returning from the rail would heat up the surge tank and the hot fuel would end up killing the efi pump because of the hot...
by chesmari
Thu Dec 31, 2015 12:33 am
Forum: Turbo and Engine Management
Topic: EFI Fuel Tank Options
Replies: 15
Views: 35927

Re: EFI Fuel Tank Options

@Chesmari Thanks for the follow up. I never thought of using a small capacity fuel cell as a surge tank. Did you use the factory lines from the top of the tank to run your lines to the lift pump? I just want to know how you ran your lines to and from the tank. Thanks again I ended up soldering alum...
by chesmari
Wed Dec 30, 2015 7:13 am
Forum: Exterior Tech
Topic: Te51 chin spoiler
Replies: 3
Views: 9515

Re: Te51 chin spoiler

VW MKI Golf 2 piece Duckbill maybe?

Image

Ryan
by chesmari
Wed Dec 30, 2015 6:41 am
Forum: Turbo and Engine Management
Topic: EFI Fuel Tank Options
Replies: 15
Views: 35927

Re: EFI Fuel Tank Options

Finished up my swap this summer on my KE30. I am using the stock tank feeding the pump through the drain plug and returning fuel back to the top of the tank. The pump is failing on me and I am sure it is due to fuel starvation. Has anyone used the stock tank on the KE30 / TE31 for their EFI setup? ...
by chesmari
Sun Dec 27, 2015 8:58 pm
Forum: Turbo and Engine Management
Topic: SR20DET Manifold to T-engines
Replies: 5
Views: 11482

Re: SR20DET Manifold to T-engines

As a follow up, saw this post in Toymods: http://www.toymods.org.au/forums/threads/31201-3T-GTE-Tech/page72?highlight=SR20DET Hi Steeko, Since I am currently running an SR20 topmount ebay stainless manifold and previously a factory cast SR20 manifold on my 3T I'll jump in! Port spacing is 'almost' i...
by chesmari
Sun Dec 27, 2015 7:35 pm
Forum: Turbo and Engine Management
Topic: SR20DET Manifold to T-engines
Replies: 5
Views: 11482

SR20DET Manifold to T-engines

Has anyone ever considered getting or have done SR20DET Turbo manifold, chop off the flange and weld a T-series exhaust flange onto it? Seems very identical in spacing. Plenty of inexpensive SR20 manifolds out there, just find a shop that TIG welds and have a budget turbo manifold with several of st...
by chesmari
Sun Dec 27, 2015 7:23 pm
Forum: Project Gallery
Topic: 3TGTE37
Replies: 12
Views: 22232

Re: 3TGTE37

BOBLOOK wrote:
caps014.jpg
Wow Ryan time for an pinned crank
I will when the time comes to rebuild the engine.....


Ryan
by chesmari
Wed Dec 23, 2015 3:42 pm
Forum: Chassis and Suspension
Topic: rear axle swaps
Replies: 12
Views: 31036

Re: rear axle swaps

I did this with my TE-37 Ford 8.8 Conversion - 95 & Up Ford Explorer -Spare Passenger side axle to replace driver side axle in order to center the differential. *4L10 - 4.10 Limited Slip *3L73 - 3.73 Limited Slip Explorer 8.8 Measurements: Weight (complete assembly w/ brakes etc.): 174 lb. O.D. ...
by chesmari
Tue Dec 22, 2015 5:11 am
Forum: General Parts
Topic: TE72 and TE28 in Pick your Part
Replies: 2
Views: 4831

Re: TE72 and TE28 in Pick your Part

TE28 is gone. TE72 is picked apart....

Ryan
by chesmari
Fri Dec 11, 2015 6:34 am
Forum: General Parts
Topic: TE72 and TE28 in Pick your Part
Replies: 2
Views: 4831

TE72 and TE28 in Pick your Part

I just visited a pick your part yard located in 1232 N Blinn Ave, Wilmington, CA 90744

There I saw a TE72 and a TE28, seems like more parts are available for picking.

Good luck.


Ryan